Remotec ZTS-110 Specifications

1 ZTS-100 (Z-Thermostat)

10 ZTS-100 Z-Thermostat Operations The following section will guide you through the set up processes for your ZTS-100. Different listening nodes

11 Normal Operation Mode Change Operation mode Note 1: In Heat mode => it displays “HEAT” if ELECTH is selected. => it display

12 Select Fan mode Step Procedure / Description LCD indication 1 Press “Fan” key once to change the Fan mode: FAN AUTO -> FAN ON FAN AUTO: Ele

13 3 Press “Prog” key once to select PROG mode: PERMANENT OVERRIDE: Permanent override the schedule until user change back to “PROG ON”. Override

14 3 In AUTO mode, user needs to set heat and cool set points temperature. Press Up/Down key to adjust auto heat set point temperature in AUTO HEAT

15 Setting mode: Step Procedure / Description LCD indication 1 Press and hold “Mode” key for 2 seconds to entry the setting mode. Day will keep

16 5 Press “Prog＂ key once to confirm the setting and it will go to temperature F -> C selection. Press Up/Down key to toggle the temperature F

17 9 Press “Prog＂ key once to confirm the setting and it will go to the Home page. Setting schedule Default schedule: Event Time Heat C

18 2 Press “Prog＂ key once to confirm the setting and it will go to event mode. Press Up/Down key to select the event (WAKE -> AWAY -> HOME -

19 5 Press and hold “UP” and “DOWN” key for 2 seconds to disable / enable event during the time setting. If the event is disabled, “OFF” will be dis

2 Table of Contents Introduction ...3 Features list ...

20 Z-Wave Add (Inclusion) / Delete (Exclusion) Mode Symbol Inclusion and Exclusion Mode Key Description N/A N/A N/A N/A Add (Inclusion) / Dele

21 3 If the ZTS-100 is removed from the network, it shows no connection. Exclusion is completed. 4 Press “Home＂ key once to go back to the home p

22 4 Press “Home＂ key once to go back to the home page. Filter counter Step Procedure / Description LCD indication 1 Press and hold “Fan”

23 Press “Home＂ key once to go back to the Home page. 4 FILTER icon will be shown on the screen at Home page when the usage hours were reached to s

24 1. Clock : 12:00am 2. Day: Mon 3. Temperature scale: F 4. Swing : 2F 5. Diff: 2F 6. Default schedule 7. Operation mode: OFF 8. Default Hea

25 Out of temperature range indication Step Procedure / Description LCD indication 1 HI icon will be displayed on LCD if temperature excess the me

26 comfort period. This option allows the choice whether to use Advanced Recovery under Setting Mode. (Recovery works in heat, cool and auto mode. M

27 Short cycle start up protection To protect the compressor / Heat pump, those outputs forced off until 3minutes count down finished. Those outputs

28 COOL Mode: thermostat controls the temperature according to the following diagram Example for Cooling: (Set point = 80 °F, Swing = 1 °F)

29 TECHNICAL SPECIFICATIONS Model no. BW8030US (ZTS-100US) BW8030AU (ZTS-100AU) BW8030EU (ZTS-100EU) RF frequency 908.4MHz (US) (ZTS-100US) 921.4MHz

3 ZTS-100 Z-Thermostat Introduction Welcome to the Z-Wave world of home automation, your ZTS-100 Z-Thermostat (Figure 1) is a comfort control

30 CHECKING THE ACCESSORIES After opening the cover of the packing box, check that the following accessories are included. • ZTS-100: Z-Thermosta

4 Heat Pump change over valve: z Selectable change over with cool or with heat Power: z Powered by alkaline batteries AA x 4pcs or 24Vac

5 Glossary Device or Node Devices and nodes are all terms to describe an individual Z-Wave device. These are all interchangeable when setting up you

6 Physical Installation and Wiring L CAUTION − Read the enclosed instructions carefully before installing your new Z-Thermostat. Pay close attentio

7 Important! The ZTS-100 can be powered by alkaline batteries AA x 4pcs or 24Vac. Connect the “24Vac Common” (typically the black wire/terminal) an

8 Jumper settings for ELECTH-HPUMP and HE-HG: Jumper Function Description Set to ELECTH for non heat pump system Set to HPUMP for heat pump system

9 Mounting: 1. Open the ZTS-100 by pushing the hook (Figure 5) 2. Install AAx4pcs batteries if using battery power (Alkaline batteries are recommen